18.12.2018 ZCU104
Материал из SRNS
Lipa (обсуждение | вклад) (→Petalinux) |
Lipa (обсуждение | вклад) (→Petalinux) |
||
| Строка 17: | Строка 17: | ||
</source> | </source> | ||
| − | Для работы eth-phy | + | Для работы eth-phy: |
| + | <source lang="bash"> | ||
| + | &gem3{ | ||
| + | status = "okay"; | ||
| + | phy-handle = <&phy0>; | ||
| + | phy-mode = "rgmii-id"; | ||
| + | |||
| + | xlnx,eth-mode = <0x1>; | ||
| + | |||
| + | mdio { | ||
| + | status = "okay"; | ||
| + | #address-cells = <1>; | ||
| + | #size-cells = <0>; | ||
| + | phy0: phy@12 { | ||
| + | compatible = "ethernet-phy-ieee802.3-c22"; | ||
| + | device_type = "ethernet-phy"; | ||
| + | |||
| + | reg = <12>; | ||
| + | ti,rx-internal-delay = <0x7>; | ||
| + | ti,tx-internal-delay = <0x7>; | ||
| + | ti,fifo-depth = <0x01>; | ||
| + | ti,min-output-impedance; | ||
| + | ti,dp83867-rxctrl-strap-quirk; | ||
| + | status = "okay"; | ||
| + | }; | ||
| + | }; | ||
| + | }; | ||
| + | </source> | ||
| + | |||
[[Категория:HOWTO]] | [[Категория:HOWTO]] | ||
Версия 16:56, 3 апреля 2019
Petalinux
Создать проект petalinux
$ petalinux-create --type project --template zynqMP --name <PROJECT>
Для работы eth-phy:
&gem3{
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
xlnx,eth-mode = <0x1>;
mdio {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
phy0: phy@12 {
compatible = "ethernet-phy-ieee802.3-c22";
device_type = "ethernet-phy";
reg = <12>;
ti,rx-internal-delay = <0x7>;
ti,tx-internal-delay = <0x7>;
ti,fifo-depth = <0x01>;
ti,min-output-impedance;
ti,dp83867-rxctrl-strap-quirk;
status = "okay";
};
};
};
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
xlnx,eth-mode = <0x1>;
mdio {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
phy0: phy@12 {
compatible = "ethernet-phy-ieee802.3-c22";
device_type = "ethernet-phy";
reg = <12>;
ti,rx-internal-delay = <0x7>;
ti,tx-internal-delay = <0x7>;
ti,fifo-depth = <0x01>;
ti,min-output-impedance;
ti,dp83867-rxctrl-strap-quirk;
status = "okay";
};
};
};
[ Хронологический вид ]Комментарии
Войдите, чтобы комментировать.